How to Deploy Google BBR on CentOS 7

BBR (Bottleneck Bandwidth and RTT) is a new congestion control algorithm which is contributed to the Linux kernel TCP stack by Google. With BBR in place, a Linux server can get significantly increased throughput and reduced latency for connections. Besides, it’s easy to deploy BBR because this algorithm requires only updates on the sender side, not in the network or on the receiver side.

In this article, I will show you how to deploy BBR on a Vultr CentOS 7 KVM server instance.

Prerequisites

• A Vultr CentOS 7 x64 server instance.
• A sudo user.

Step 1: Upgrade the kernel using the ELRepo RPM repository

In order to use BBR, you need to upgrade the kernel of your CentOS 7 machine to 4.9.0. You can easily get that done using the ELRepo RPM repository.

Before the upgrade, you can take a look at the current kernel:

uname -r

This command should output a string which resembles:

3.10.0-514.2.2.el7.x86_64

As you see, the current kernel is 3.10.0.

update and install the ELRepo repo:

sudo yum update
sudo rpm --import https://www.elrepo.org/RPM-GPG-KEY-elrepo.org
sudo rpm -Uvh http://www.elrepo.org/elrepo-release-7.0-2.el7.elrepo.noarch.rpm

Install the 4.9.0 kernel using the ELRepo repo:

sudo yum --enablerepo=elrepo-kernel install kernel-ml -y

Confirm the result:

rpm -qa | grep kernel

If the installation is successful, you should see kernel-ml-4.9.0-1.el7.elrepo.x86_64 among the output list:

kernel-ml-4.9.0-1.el7.elrepo.x86_64
kernel-3.10.0-514.el7.x86_64
kernel-tools-libs-3.10.0-514.2.2.el7.x86_64
kernel-tools-3.10.0-514.2.2.el7.x86_64
kernel-3.10.0-514.2.2.el7.x86_64
Now, you need to enable the 4.9.0 kernel by setting up the default grub2 boot entry.

Show all entries in the grub2 menu:

sudo egrep ^menuentry /etc/grub2.cfg | cut -f 2 -d \'

The result should resemble:

CentOS Linux 7 Rescue a0cbf86a6ef1416a8812657bb4f2b860 (4.9.0-1.el7.elrepo.x86_64)
CentOS Linux (4.9.0-1.el7.elrepo.x86_64) 7 (Core)
CentOS Linux (3.10.0-514.2.2.el7.x86_64) 7 (Core)
CentOS Linux (3.10.0-514.el7.x86_64) 7 (Core)
CentOS Linux (0-rescue-bf94f46c6bd04792a6a42c91bae645f7) 7 (Core)

Since the line count starts at 0 and the 4.9.0 kernel entry is on the second line, set the default boot entry as 1:

sudo grub2-set-default 1

Reboot the system:

sudo shutdown -r now

When the server is back online, log back in and rerun the uname command to confirm that you are using the correct Kernel:

uname -r

You should see the result as below:

4.9.0-1.el7.elrepo.x86_64

Step 2: Enable BBR

In order to enable the BBR algorithm, you need to modify the sysctl configuration as follows:

echo 'net.core.default_qdisc=fq' | sudo tee -a /etc/sysctl.conf
echo 'net.ipv4.tcp_congestion_control=bbr' | sudo tee -a /etc/sysctl.conf
sudo sysctl -p

Now, you can use the following commands to confirm that BBR is enabled:

sudo sysctl net.ipv4.tcp_available_congestion_control

The output should resemble:

net.ipv4.tcp_available_congestion_control = bbr cubic reno

Next, verify with:

sudo sysctl -n net.ipv4.tcp_congestion_control

The output should be:

bbr

Finally, check that the kernel module was loaded:

lsmod | grep bbr

The output will be similar to:

tcp_bbr                16384  0

reference 1

reference 2